Angelo D&233;cor

300 GPH (1200LPH) Fountain Pump

Specifications

Item#: AD40300

No Data

300 GPH Fountain Specifications

Output Connection	1/2″ – 3/4″
Cord Length	16 ft / 5 m
Power Supply	120v 60 Hz
Power Consumption	30 watts
Flow Rate	300 GPH / 1200 LPH
Stop Height	78 inches / 200 cm
Dimension LxWxH(mm)	90x58x72
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

300 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

40 GPH (180LPH) Fountain Pump

Specifications

Item#: AD40042

No Data

40 GPH Fountain Specifications

Output Connection	5/16″
Cord Length	6.5 ft / 2 m
Power Supply	120v 60 Hz
Power Consumption	2 watts
Flow Rate	40 GPH / 180 LPH
Stop Height	20 inches / 50 cm
Dimension LxWxH(mm)	40x35x30
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

40 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

400 GPH Fountain Specifications

Output Connection	1/2″ – 3/4″
Cord Length	15 ft / 4.6 m
Power Supply	120v 60 Hz
Power Consumption	20 watts
Flow Rate	400 GPH / 1500 LPH
Stop Height	78 inches / 200 cm
Dimension LxWxH(mm)	115x60x75
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

400 GPH Fountain Pump Assembly

No Data

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

225 GPH (850LPH) Fountain Pump

Specifications

Item#: AD40225

No Data

There are currently no videos for this product.

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

225 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

250 GPH (1000LPH) Fountain Pump

Specifications

Item#: AD40250

No Data

250 GPH Fountain Specifications

Output Connection	1/2″ – 3/4″
Cord Length	16 ft / 5 m
Power Supply	120v 60 Hz
Power Consumption	19 watts
Flow Rate	250 GPH / 1000 LPH
Stop Height	66 inches / 170 cm
Dimension LxWxH(mm)	90x58x72
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

250 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

180 GPH (680LPH) Fountain Pump

Specifications

Item#: AD40180

No Data

180 GPH Fountain Specifications

Output Connection	1/2″ – 3/8″
Cord Length	10 ft / 3 m
Power Supply	120v 60 Hz
Power Consumption	11 watts
Flow Rate	180 GPH / 680 LPH
Stop Height	53 inches / 135 cm
Dimension LxWxH(mm)	70x50x59
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

180 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

150 GPH (600LPH) Fountain Pump

Specifications

Item#: AD40150

No Data

150 GPH Fountain Specifications

Output Connection	1/2″ – 3/8″
Cord Length	10 ft / 3 m
Power Supply	120v 60 Hz
Power Consumption	10 watts
Flow Rate	158 GPH / 600 LPH
Stop Height	47 inches / 120 cm
Dimension LxWxH(mm)	60x50x47
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

150 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

110 GPH (450LPH) Fountain Pump

Specifications

Item#: AD40110

No Data

110 GPH Fountain Specifications

Output Connection	1/2″ – 3/8″
Cord Length	10 ft / 3 m
Power Supply	120v 60 Hz
Power Consumption	6.5 watts
Flow Rate	118 GPH / 450 LPH
Stop Height	39 inches / 100 cm
Dimension LxWxH(mm)	60×50×47
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.

CAUTION: This Pump Has Been Evaluated For Use With Water Only

110 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

80 GPH (300LPH) Fountain Pump

Specifications

Item#: AD40080

No Data

80 GPH Fountain Specifications

Output Connection	1/2″ – 3/8″
Cord Length	10 ft / 3 m
Power Supply	120v 60 Hz
Power Consumption	5 watts
Flow Rate	80 GPH / 370 LPH
Stop Height	29 inches / 75 cm
Dimension LxWxH(mm)	60x50x47
Approved	CUL

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

80 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.

Angelo D&233;cor

55 GPH (200LPH) Fountain Pump

Specifications

Item#: AD40055

No Data

55 GPH Fountain Specifications

Output Connection	1/2″ – 3/8″
Cord Length	10 ft / 3 m
Power Supply	120v 60 Hz
Power Consumption	2 watts
Flow Rate	55 GPH / 200 LPH
Stop Height	27 inches / 70 cm
Dimension LxWxH(mm)	48x44x32
Approved	CUL

*Note: Control valve may not be exactly as shown.

Intended Use – We recommend this unit for outdoor use.
This fountain is designed for outdoor use. While it can be used indoors, there will be moisture generated in the surrounding area. Therefore, care should be taken to use only in areas where water will not cause damage to hardwood floors, carpet, etc. It should also not be used indoors in areas of frequent foot traffic, as the moisture will cause slippery floor surfaces.

Pump Care – Pumps should always be plugged into a grounded GFCI receptacle.
Pumps should always be fully submersed in water. Low water levels may cause burnout, voiding your warranty.
We recommended that you run the pump in a bucket of water first, to “prime the pump” and insure proper operation. The power cord should extend or hang lower than the wall plug socket; this is to prevent water drops from making contact with the plug or electrical supply outlet. These pumps should be cleaned regularly to insure long life. Hard water buildup on impeller will cause reduced efficiency. The diagram below shows proper disassembly procedures.

Winter Care – We Strongly Suggest Storage in areas with Harsh Winter Conditions!
These units are designed for outdoor use during the spring, summer, and fall months. The unit should be stored properly in areas with harsh winter conditions, with all water removed, preferably in shelter. The pump must be drained of all water.

Maintenance – Keep it Clean!
Your fountain will work better, and last longer, when kept clean using a soft cloth and mild soap on a regular basis. At minimum, you should change the water with a blast from your hose, and keep leaves and debris out of the unit. Hard water should be avoided if possible, to reduce staining and paint discoloration. Small chips or minor paint erosion can easily be fixed using commonly available “hobby paints” that are close to the existing finish.

WARNING: To reduce the risk of electrical shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
CAUTION: This Pump Has Been Evaluated For Use With Water Only

55 GPH Fountain Pump Assembly

1 year limited warranty, for more information about our warranty policies visit our customer support section.